Server room thermostat recommendation

August 24, 2015, 12:55 pm

≫ Next: Relocating ZBrush ZStartup directory?

≪ Previous: Sandisk X300S 256G High Failure Rate

$

0

0

Server room thermostat recommendation

posted by Ryan Lynch on Aug. 24, 2015, 3:55 p.m.

Does anyone have a good recommendation for a server room thermostat? It needs to be able to accomplish lead lag between two separate AC systems. Remote functions would be plus but not required. Our contractor wants to put a commercial model, the Venstar T2900 which would be replacing an older Trane T-stat. I'm hoping that there is a model which has had reasonable success in server room environments. Thanks! Ryan Ryan Lynch 76.lynch@gmail.com

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Does anyone have a good recommendation for a server room thermostat? It needs to be able to accomplish lead lag between two separate AC systems. Remote functions would be plus but not required. Our contractor wants to put a commercial model, the Venstar T2900 which would be replacing an older Trane T-stat. I'm hoping that there is a model which has had reasonable success in server room environments. Thanks! Ryan Ryan Lynch 76.lynch@gmail.com

---

Relocating ZBrush ZStartup directory?

August 24, 2015, 1:40 pm

≫ Next: Baselight Blackboard 2 USB Extender

≪ Previous: Server room thermostat recommendation

$

0

0

Relocating ZBrush ZStartup directory?

posted by Jean-Francois Panisset on Aug. 24, 2015, 4:40 p.m. (1 day ago)

Has anyone found a way to tell ZBrush that its ZStartup directory lives somewhere else than in the application installation directory? That directory hierarchy is supposed to be to add custom stuff, and ZBrush wants to write to it on startup. This is bad for a number of reasons: - you can't have project or user specific customization, or customization that follows the user to a different machine - you are opening up permissions on C:\Program Files (x86) (their install does this for you) - you can't relocate the app to a read-only share JF

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Has anyone found a way to tell ZBrush that its ZStartup directory lives somewhere else than in the application installation directory? That directory hierarchy is supposed to be to add custom stuff, and ZBrush wants to write to it on startup. This is bad for a number of reasons: - you can't have project or user specific customization, or customization that follows the user to a different machine - you are opening up permissions on C:\Program Files (x86) (their install does this for you) - you can't relocate the app to a read-only share JF

Baselight Blackboard 2 USB Extender

August 26, 2015, 6:10 am

≫ Next: Baselight Blackboard 2 USB Extender

≪ Previous: Relocating ZBrush ZStartup directory?

$

0

0

Baselight Blackboard 2 USB Extender

posted by  on Aug. 26, 2015, 9:10 a.m.

Hey everyone, does anyone know a USB 2.0 Extender (to Copper or Fiber) that works for sure with the Baselight Blackboard 2 panel? The Icron and Ihse extenders from us don't work with the panel - maybe someone has a working setup. The Filmlight guys only know of a few that use Gefen extendern, but could not tell me exactly which one. Thank you and cheers Jatha -- /////////////////////////// /////////////////////////// //////////////////// JATHAVAN SRIRAM HARVEST /DIGITAL AGRICULTURE GMBH Alter Wandrahm 8-9 20457 Hamburg Phone: +49/ 40 411 880 500 sriram@harvest-postproduction.com www.harvest-postproduction.com Managing Director: Florian Arlart Trade register: Harvest Digital Agriculture GmbH, HRB 121482 The contents of this email are confidential. If you are not the intended recipient, please notify us as soon as possible: you should not copy, forward, disclose or use the contents. Start may monitor outgoing and incoming mail for business purposes.

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Hey everyone, does anyone know a USB 2.0 Extender (to Copper or Fiber) that works for sure with the Baselight Blackboard 2 panel? The Icron and Ihse extenders from us don't work with the panel - maybe someone has a working setup. The Filmlight guys only know of a few that use Gefen extendern, but could not tell me exactly which one. Thank you and cheers Jatha -- /////////////////////////// /////////////////////////// //////////////////// JATHAVAN SRIRAM HARVEST /DIGITAL AGRICULTURE GMBH Alter Wandrahm 8-9 20457 Hamburg Phone: +49/ 40 411 880 500 sriram@harvest-postproduction.com www.harvest-postproduction.com Managing Director: Florian Arlart Trade register: Harvest Digital Agriculture GmbH, HRB 121482 The contents of this email are confidential. If you are not the intended recipient, please notify us as soon as possible: you should not copy, forward, disclose or use the contents. Start may monitor outgoing and incoming mail for business purposes.

Baselight Blackboard 2 USB Extender

August 26, 2015, 8:50 am

≫ Next: Cable suppliers in Vancouver

≪ Previous: Baselight Blackboard 2 USB Extender

$

0

0

Baselight Blackboard 2 USB Extender

posted by Dan Young on Aug. 26, 2015, 11:50 a.m.

I thought the blackboard typically goes right into the host node? You would certainly need an active connection for it..... have you tried talking to Bradley? DY On 08/26/2015 06:08 AM, Jathavan Sriram | Harvest wrote: Hey everyone, does anyone know a USB 2.0 Extender (to Copper or Fiber) that works for sure with the Baselight Blackboard 2 panel? The Icron and Ihse extenders from us don't work with the panel - maybe someone has a working setup. The Filmlight guys only know of a few that use Gefen extendern, but could not tell me exactly which one. Thank you and cheers Jatha -- /////////////////////////// /////////////////////////// //////////////////// JATHAVAN SRIRAM HARVEST /DIGITAL AGRICULTURE GMBH Alter Wandrahm 8-9 20457 Hamburg Phone: +49/ 40 411 880 500 sriram@harvest-postproduction.com www.harvest-postproduction.com Managing Director: Florian Arlart Trade register: Harvest Digital Agriculture GmbH, HRB 121482 The contents of this email are confidential. If you are not the intended recipient, please notify us as soon as possible: you should not copy, forward, disclose or use the contents. Start may monitor outgoing and incoming mail for business purposes. To unsubscribe from the list send a blank e-mail to mailto:studiosysadmins-discuss-request@studiosysadmins.com?subject=unsubscribe

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

I thought the blackboard typically goes right into the host node? You would certainly need an active connection for it..... have you tried talking to Bradley? DY On 08/26/2015 06:08 AM, Jathavan Sriram | Harvest wrote: Hey everyone, does anyone know a USB 2.0 Extender (to Copper or Fiber) that works for sure with the Baselight Blackboard 2 panel? The Icron and Ihse extenders from us don't work with the panel - maybe someone has a working setup. The Filmlight guys only know of a few that use Gefen extendern, but could not tell me exactly which one. Thank you and cheers Jatha -- /////////////////////////// /////////////////////////// //////////////////// JATHAVAN SRIRAM HARVEST /DIGITAL AGRICULTURE GMBH Alter Wandrahm 8-9 20457 Hamburg Phone: +49/ 40 411 880 500 sriram@harvest-postproduction.com www.harvest-postproduction.com Managing Director: Florian Arlart Trade register: Harvest Digital Agriculture GmbH, HRB 121482 The contents of this email are confidential. If you are not the intended recipient, please notify us as soon as possible: you should not copy, forward, disclose or use the contents. Start may monitor outgoing and incoming mail for business purposes. To unsubscribe from the list send a blank e-mail to mailto:studiosysadmins-discuss-request@studiosysadmins.com?subject=unsubscribe

Cable suppliers in Vancouver

August 26, 2015, 9:40 am

≫ Next: Finder + NFS partial fix?

≪ Previous: Baselight Blackboard 2 USB Extender

$

0

0

Cable suppliers in Vancouver

posted by James Braid on Aug. 26, 2015, 12:40 p.m.

Who do people like for cables in Vancouver? Need someone who has stock for reasonably large quantities of DVI, USB, IEC power, etc... Any recommendations or pointers to favourite suppliers would be appreciated.

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Who do people like for cables in Vancouver? Need someone who has stock for reasonably large quantities of DVI, USB, IEC power, etc... Any recommendations or pointers to favourite suppliers would be appreciated.

Finder + NFS partial fix?

August 26, 2015, 1:15 pm

≫ Next: L2TP Client for Solaris?

≪ Previous: Cable suppliers in Vancouver

$

0

0

Finder + NFS partial fix?

posted by Brian Krusic on Aug. 26, 2015, 4:15 p.m.

Hi, Any one tried commenting out /net from /etc/auto-master? If so, what have you noticed? Weve seen less Finder wack, seems in fact a bit better. Just curious what the community has seen. - Brian A good day is when no one shows up... and you don't have to go anywhere."

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Hi, Any one tried commenting out /net from /etc/auto-master? If so, what have you noticed? Weve seen less Finder wack, seems in fact a bit better. Just curious what the community has seen. - Brian A good day is when no one shows up... and you don't have to go anywhere."

L2TP Client for Solaris?

August 26, 2015, 3:30 pm

≫ Next: Smoke 2016 and Blackmagic

≪ Previous: Finder + NFS partial fix?

$

0

0

L2TP Client for Solaris?

posted by William Sandler on Aug. 26, 2015, 6:30 p.m. (1 day ago)

We're trying to connect a Solaris server to a Windows L2TP server with PSK (no cert). Anyone have any thoughts on how to accomplish this? William Sandler All Things Media, LLC Office:201.818.1999 Ex 158. william.sandler@allthingsmedia.com

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

We're trying to connect a Solaris server to a Windows L2TP server with PSK (no cert). Anyone have any thoughts on how to accomplish this? William Sandler All Things Media, LLC Office:201.818.1999 Ex 158. william.sandler@allthingsmedia.com

Smoke 2016 and Blackmagic

August 27, 2015, 9:15 am

≫ Next: Samsung SSD Deals on B&H for 1TB and 2TB EVO

≪ Previous: L2TP Client for Solaris?

$

0

0

Smoke 2016 and Blackmagic

posted by Ken Spickler on Aug. 27, 2015, 12:15 p.m.

Has anyone got experience running Smoke 2016 on Mac with a Blackmagic UltraStudio 4K? We've just built a system and can't get a good video signal out of it. With the 10.4.x BM driver we always get a green line through VBI, and earlier drivers are unstable. Thanks, Ken

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Has anyone got experience running Smoke 2016 on Mac with a Blackmagic UltraStudio 4K? We've just built a system and can't get a good video signal out of it. With the 10.4.x BM driver we always get a green line through VBI, and earlier drivers are unstable. Thanks, Ken

---

Samsung SSD Deals on B&H for 1TB and 2TB EVO

August 27, 2015, 4:00 pm

≫ Next: L21-30P -> C19 PDU in Toronto?

≪ Previous: Smoke 2016 and Blackmagic

$

0

0

Samsung SSD Deals on B&H for 1TB and 2TB EVO

posted by Saker Klippsten on Aug. 27, 2015, 7 p.m. (1 day ago)

Some nice deals right now for the 1TB EVO $334 and 2TB EVO $747 No taxes shipping to CA. ends the 29th. http://www.bhphotovideo.com/c/product/1086227-REG/samsung_mz_75e1t0b_am_853_evo_1tb_2_5.html -S

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Some nice deals right now for the 1TB EVO $334 and 2TB EVO $747 No taxes shipping to CA. ends the 29th. http://www.bhphotovideo.com/c/product/1086227-REG/samsung_mz_75e1t0b_am_853_evo_1tb_2_5.html -S

L21-30P -> C19 PDU in Toronto?

August 28, 2015, 7:40 am

≫ Next: fire/smoke detectors & server rooms

≪ Previous: Samsung SSD Deals on B&H for 1TB and 2TB EVO

$

0

0

L21-30P -> C19 PDU in Toronto?

posted by Andrew Klaassen on Aug. 28, 2015, 10:40 a.m.

We need a couple of PDUs with an L21-30P plug and at least four C19 receptacles as soon as we can get 'em. Anybody have one or two lying around, or know where we could pick a couple up quickly? Thanks! Andrew To unsubscribe from the list send a blank e-mail to mailto:studiosysadmins-discuss-request@studiosysadmins.com?subject=unsubscribe

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

We need a couple of PDUs with an L21-30P plug and at least four C19 receptacles as soon as we can get 'em. Anybody have one or two lying around, or know where we could pick a couple up quickly? Thanks! Andrew To unsubscribe from the list send a blank e-mail to mailto:studiosysadmins-discuss-request@studiosysadmins.com?subject=unsubscribe

fire/smoke detectors & server rooms

August 28, 2015, 8:15 am

≫ Next: 10GB Fiber and SFP+ Cables in store in Toronto

≪ Previous: L21-30P -> C19 PDU in Toronto?

$

0

0

fire/smoke detectors & server rooms

posted by Rob LaRose on Aug. 28, 2015, 11:15 a.m.

Good morning! A while back, during a test of our fire alarm systems, both of our server room AC units were disabled. Turns out the folks doing the tests had neglected to reset the switch. Fine. But I have to admit I wasnt aware that the fire alarm system would shut them off at all. Ive since done some reading and from what I can tell, a smoke/particulate detector is supposed to shut off AC & other air handlers/blowers to prevent spreading smoke / feeding the fire. What Im not clear on is the scope. Should my in-room ACs only be shut down by a sensor being tripped IN THE ROOM, or should I expect any alarm condition (on our floor or below us) to result in a shutdown of all my blowers? The building super says the latter (any alarm will shut me off) but that seems wrong/crazy to me. Anyone know the skinny on regulation (Im in NYC) and/or standard practice for these things? Rob To unsubscribe from the list send a blank e-mail to mailto:studiosysadmins-discuss-request@studiosysadmins.com?subject=unsubscribe

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Good morning! A while back, during a test of our fire alarm systems, both of our server room AC units were disabled. Turns out the folks doing the tests had neglected to reset the switch. Fine. But I have to admit I wasnt aware that the fire alarm system would shut them off at all. Ive since done some reading and from what I can tell, a smoke/particulate detector is supposed to shut off AC & other air handlers/blowers to prevent spreading smoke / feeding the fire. What Im not clear on is the scope. Should my in-room ACs only be shut down by a sensor being tripped IN THE ROOM, or should I expect any alarm condition (on our floor or below us) to result in a shutdown of all my blowers? The building super says the latter (any alarm will shut me off) but that seems wrong/crazy to me. Anyone know the skinny on regulation (Im in NYC) and/or standard practice for these things? Rob To unsubscribe from the list send a blank e-mail to mailto:studiosysadmins-discuss-request@studiosysadmins.com?subject=unsubscribe

10GB Fiber and SFP+ Cables in store in Toronto

August 28, 2015, 8:25 am

≫ Next: What's your nfs rsize & wsize?

≪ Previous: fire/smoke detectors & server rooms

$

0

0

10GB Fiber and SFP+ Cables in store in Toronto

posted by Bobby Jain on Aug. 28, 2015, 11:25 a.m.

Hello, Does anyone know of a store I can stop in at to buy fiber and SFP+ cables? I am a bit short, and need them for this weekend. Thanks!

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Hello, Does anyone know of a store I can stop in at to buy fiber and SFP+ cables? I am a bit short, and need them for this weekend. Thanks!

What's your nfs rsize & wsize?

August 28, 2015, 9:30 am

≫ Next: Vancouver Power Outage

≪ Previous: 10GB Fiber and SFP+ Cables in store in Toronto

$

0

0

What's your nfs rsize & wsize?

posted by Chris Banal on Aug. 28, 2015, 12:30 p.m.

Hello, It's been a while since I last looked at this and there are several considerations for setting nfs rsize & wsize but I'm curious what folks are doing these days? Do you have multiple mounts with small and large settings tailored to the traffic type? If so what sizes do you use for which types of traffic with which storage product? If you have just one mount, what's your generic setting? If you're using a large rsizes, do you see inflated IO and memory utilization due to read ahead and buffers? A while back we found that some tasks had thousands of files open and the read buffers were based on the mounted block size. This caused several gigabytes in memory overhead. At the moment we're using 32k for everything with Isilon storage and it's time to take another look. Thanks, - Chris

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Hello, It's been a while since I last looked at this and there are several considerations for setting nfs rsize & wsize but I'm curious what folks are doing these days? Do you have multiple mounts with small and large settings tailored to the traffic type? If so what sizes do you use for which types of traffic with which storage product? If you have just one mount, what's your generic setting? If you're using a large rsizes, do you see inflated IO and memory utilization due to read ahead and buffers? A while back we found that some tasks had thousands of files open and the read buffers were based on the mounted block size. This caused several gigabytes in memory overhead. At the moment we're using 32k for everything with Isilon storage and it's time to take another look. Thanks, - Chris

Vancouver Power Outage

August 29, 2015, 6:35 pm

≫ Next: nVidia GRID is not dead apparently

≪ Previous: What's your nfs rsize & wsize?

$

0

0

Vancouver Power Outage

posted by Saker Klippsten on Aug. 29, 2015, 9:35 p.m. (2 days ago)

Fun Times!! UPDATE 1:10 p.m. Stanley Park has been shut down UPDATE 1:25 p.m. BC Hydro says there are 200,000 customers without power UPDATE 1:54 p.m. SkyTrains Expo and Millenium Lineis running, with delays UPDATE 1:54 p.m. PNE Playland is still open, but 75% of rides are closed UPDATE 2:55 p.m. PNE is closed for the day, those who purchased ride passes will receive a complimentary pass for another day UPDATE 3:17 p.m. Nearly 300,000 customers without power in Metro Vancouver alone, over 325,000 around B.C. UPDATE 3:27 p.m. PNE is back open for the day, and free for everyone UPDATE 4:20 p.m. Over 400,000 customers without power in Metro Vancouver Hope everyone has their DR Plan in place :) http://www.vancitybuzz.com/2015/08/vancouver-wind-storm-power-outages/

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Fun Times!! UPDATE 1:10 p.m. Stanley Park has been shut down UPDATE 1:25 p.m. BC Hydro says there are 200,000 customers without power UPDATE 1:54 p.m. SkyTrains Expo and Millenium Lineis running, with delays UPDATE 1:54 p.m. PNE Playland is still open, but 75% of rides are closed UPDATE 2:55 p.m. PNE is closed for the day, those who purchased ride passes will receive a complimentary pass for another day UPDATE 3:17 p.m. Nearly 300,000 customers without power in Metro Vancouver alone, over 325,000 around B.C. UPDATE 3:27 p.m. PNE is back open for the day, and free for everyone UPDATE 4:20 p.m. Over 400,000 customers without power in Metro Vancouver Hope everyone has their DR Plan in place :) http://www.vancitybuzz.com/2015/08/vancouver-wind-storm-power-outages/

nVidia GRID is not dead apparently

August 31, 2015, 2:45 am

≫ Next: Various Maya Service Pack Installations on the same Windows machine

≪ Previous: Vancouver Power Outage

$

0

0

nVidia GRID is not dead apparently

posted by Julian Firminger on Aug. 31, 2015, 5:45 a.m.

http://www.theregister.co.uk/2015/08/30/nvidia_reveals_gpus_for_blade_servers_linux_desktop_support/ Linux VDI full support. If you believe the hype this could be a gamechanger. Julian Firminger Snr. Systems Administrator, United Broadcast Facilities Amsterdam, The Netherlands

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

http://www.theregister.co.uk/2015/08/30/nvidia_reveals_gpus_for_blade_servers_linux_desktop_support/ Linux VDI full support. If you believe the hype this could be a gamechanger. Julian Firminger Snr. Systems Administrator, United Broadcast Facilities Amsterdam, The Netherlands

---

Various Maya Service Pack Installations on the same Windows machine

August 31, 2015, 7:52 am

≫ Next: Various Maya Service Pack Installations on the same Windows machine

≪ Previous: nVidia GRID is not dead apparently

$

0

0

Various Maya Service Pack Installations on the same Windows machine

posted by Peter Nepp on Aug. 31, 2015, 10:52 a.m.

Hi there, we are looking for a way to install the several Service Packs of Maya 2016 on Windows separately instead only the latest Service Pack per Maya version. Is there a way to do this? The Windows installer seems to uninstall previous Maya/Service Pack versions accordingly. This could help us evaluating what Maya Version or Service Pack is a stable (enough) production release. Any suggestions? Thanks a lot, Peter

Thread Tags:   maya

0 Responses     0 Plus One's     0 Comments

 

Hi there, we are looking for a way to install the several Service Packs of Maya 2016 on Windows separately instead only the latest Service Pack per Maya version. Is there a way to do this? The Windows installer seems to uninstall previous Maya/Service Pack versions accordingly. This could help us evaluating what Maya Version or Service Pack is a stable (enough) production release. Any suggestions? Thanks a lot, Peter

Various Maya Service Pack Installations on the same Windows machine

August 31, 2015, 8:05 am

≫ Next: Graphics Upgrades (Gaming vs. Quadro)

≪ Previous: Various Maya Service Pack Installations on the same Windows machine

$

0

0

Various Maya Service Pack Installations on the same Windows machine

posted by Rob Aitchison on Aug. 31, 2015, 11:05 a.m.

Hi, I don't think it's worth the time investment to compare SP 1 vs. 2 etc. Take the latest one available as the odds of new bugs introduced with a later service pack are low. Cheers! On Aug 31, 2015 10:52 AM, "Peter Nepp" <content@studiosysadmins.com> wrote: Hi there, we are looking for a way to install the several Service Packs of Maya 2016 on Windows separately instead only the latest Service Pack per Maya version. Is there a way to do this? The Windows installer seems to uninstall previous Maya/Service Pack versions accordingly. This could help us evaluating what Maya Version or Service Pack is a stable (enough) production release. Any suggestions? Thanks a lot, Peter To unsubscribe from the list send a blank e-mail to mailto:studiosysadmins-discuss-request@studiosysadmins.com?subject=unsubscribe

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Hi, I don't think it's worth the time investment to compare SP 1 vs. 2 etc. Take the latest one available as the odds of new bugs introduced with a later service pack are low. Cheers! On Aug 31, 2015 10:52 AM, "Peter Nepp" <content@studiosysadmins.com> wrote: Hi there, we are looking for a way to install the several Service Packs of Maya 2016 on Windows separately instead only the latest Service Pack per Maya version. Is there a way to do this? The Windows installer seems to uninstall previous Maya/Service Pack versions accordingly. This could help us evaluating what Maya Version or Service Pack is a stable (enough) production release. Any suggestions? Thanks a lot, Peter To unsubscribe from the list send a blank e-mail to mailto:studiosysadmins-discuss-request@studiosysadmins.com?subject=unsubscribe

Graphics Upgrades (Gaming vs. Quadro)

September 1, 2015, 7:50 am

≫ Next: Panasonic 65" 4K OLED monitor

≪ Previous: Various Maya Service Pack Installations on the same Windows machine

$

0

0

Graphics Upgrades (Gaming vs. Quadro)

posted by  on Sept. 1, 2015, 10:50 a.m.

Hello All, We have a few machines with older Quadro FX3800's which I'd like to upgrade. Does anyone have a favorite gaming card that might be a better option than something like a Quadro K4000? We are primarily using After Effects and other Adobe apps as well as using these to render 3DS Max stuff. Many thanks for any feedback. Craig

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Hello All, We have a few machines with older Quadro FX3800's which I'd like to upgrade. Does anyone have a favorite gaming card that might be a better option than something like a Quadro K4000? We are primarily using After Effects and other Adobe apps as well as using these to render 3DS Max stuff. Many thanks for any feedback. Craig

Panasonic 65" 4K OLED monitor

September 2, 2015, 10:20 am

≫ Next: A/C experts in West LA ?

≪ Previous: Graphics Upgrades (Gaming vs. Quadro)

$

0

0

Panasonic 65" 4K OLED monitor

posted by Jean-Francois Panisset on Sept. 2, 2015, 1:20 p.m.

http://www.forbes.com/sites/johnarcher/2015/09/02/panasonic-goes-oled-new-65-inch-4k-tv-unveiled/ Why oh why does it have to be curved? JF

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

http://www.forbes.com/sites/johnarcher/2015/09/02/panasonic-goes-oled-new-65-inch-4k-tv-unveiled/ Why oh why does it have to be curved? JF

A/C experts in West LA ?

September 2, 2015, 11:30 am

≫ Next: OMG, new Maxon lic server?

≪ Previous: Panasonic 65" 4K OLED monitor

$

0

0

A/C experts in West LA ?

posted by Philippe Chotard on Sept. 2, 2015, 2:30 p.m.

Hi all, We're facing a humidity problem in our server room for several weeks now. Our A/C maintainers can't seem to find any solution for this, and even worse, they don't have a clue of the source of this humidity. Do you guys know any A/C experts in West LA I could show this installation to ? Not just a company that installs units from reading the manuals, but one that knows about condensation/temperature environment principles. Thanks ! chob

Thread Tags:   discuss-at-studiosysadmins

0 Responses     0 Plus One's     0 Comments

 

Hi all, We're facing a humidity problem in our server room for several weeks now. Our A/C maintainers can't seem to find any solution for this, and even worse, they don't have a clue of the source of this humidity. Do you guys know any A/C experts in West LA I could show this installation to ? Not just a company that installs units from reading the manuals, but one that knows about condensation/temperature environment principles. Thanks ! chob